Chemsol Chemroof is an elastomeric waterproofing membrane based on modified acrylic emulsion which is strongly recommended for high build waterproof membrane which adheres to the surface and provides excellent water-resistant coating for years. This coating is extremely tough and elastic and can be applied easily with the help of a roller or squeegee.

Applications

• Waterproofing plain slab and sloping roofs.
• Waterproofing of parapet walls.

Features

• Easy to apply with brush, squeegee or roller.
• Good adhesion to concrete.
• VOC free.
• Can be applied on both horizontal and vertical surfaces.
• Provides highly durable seamless waterproofing membrane.

Method of Application

1. Surface Preparation

• Surface should be clean and dry and in sound condition.
• All the surface dirt, grease, loose particles should be removed from the surface. And the surface should be washed thoroughly with clean water.
• The surface should be moist before the coat application.

2. New Surfaces

• The newly constructed surfaces shall be completely cured before coating application.

3. Cracks and Joint Treatment

• All the surface cracks from 0 - 5mm shall be opened with a 3mm angle grinder.
• The opened cracks shall be cleaned properly and filled with Chem Crack Fill an acrylic crack-filler or PU Sealant.
• Cracks more than 5mm should be repaired using polymer modified mortar of Chemfast SBR. With a cement sand ratio of 1:3 and polymer content of 10% by weight if cement. Allow it to cure as required.

4. Priming

• Apply priming coat with Chemsol Chemroof with 50% water dilution. The priming coat shall give approximate coverage of 80-100 Sqft/L depending upon the surface finish. The surface should be maintained in SSD condition prior to priming application. Chem Seal Prime can also be used for priming purpose wit 50% water dilution.

5. Application

• Mix the bucket contents thoroughly.
• The drain outlets need to be properly detailed with the coating with an additional piece of fiberglass mesh as a reinforcement.
• Apply 1st coat of Chemsol Chemroof on the surface with a coverage of 0.45 Lit/Sqm/Coat all over the surface. Let the coating air dry for minimum 6hrs.
• Apply 2nd coat of Chemsol Chemroof at an angle of 90o to the first coat and let dry for minimum 6 hrs.

6. Ponding

• Let the system air cure for 7-8 days before pond test.
• Ponding shall be done with water not more than 5 cm in height.

Precautions and Limitations

• Do not dilute Chemroof with water for coating application.
• Keep material closed when not in use.
• Vehicular or machinery movement is not recommended on the coated surface.

Technical Information

Theoretical Coverage

Per liter coverage of 1.1 m2/2 Coats is obtained on smooth concrete surface.

Pack Size

5L and 20L

Storage

Chemsol Chemroof shall be placed in a cool and dry place protected from direct sunlight.

Shelf Life

12 months for the date of manufacturing if unopened and stored properly.

Health and Safety

Wash skin with soap and water.
On eye contact wash the eyes immediately and consult a physician if irritation persists.
On ingestion consult a doctor immediately.

Chemsol Chemroof Plus is an acrylic based product with high resistance to all weather conditions and excellent UV resistance. Chemroof Plus is easy to apply with roller, brush and is environment friendly.

Applications

• Large roof areas over screed or coba.

Features

• Coating DFT of 800-1000 microns in three coats.
• 2 mm crack bridging ability all thanks to over 300% elongation.
• Excellent resistance to the weather conditions.
• Better solar reflective index.
• Low VOC content.
• Easy to apply.

Method of Application

1. Surface Preparation

• Surface should be clean and dry and in sound condition.
• All the surface dirt, grease, loose particles should be removed from the surface. And the surface should be washed thoroughly with clean water.
• Ensure that proper slope is provided and there is no water stagnation.
• All other previous coatings if any shall be completely removed.

2. New Surfaces

• The newly constructed surfaces shall be completely cured before coating application.

3. Cracks and Joint Treatment

• All the surface cracks shall be opened with a 3mm angle grinder.
• The opened cracks shall be cleaned properly and filled with a suitable acrylic crack-filler or PU Sealant.
• Cracks more than 5mm should be repaired using polymer modified mortar with Chemfast SBR. With a cement sand ratio of 1:3 and polymer content of 10% by weight if cement. Allow it to cure as required.

4. Priming

• Apply priming coat with Chemsol Chemroof Plus with 100% water dilution. The priming coat shall give approximate coverage of 80-100 Sqft/L depending upon the
  surface finish. The surface should be maintained in SSD condition prior to priming application. Priming can also be done with Chemseal Prime with 100% dilution.

5. Application

• Mix the bucket contents thoroughly.
• The drain outlets need to be properly detailed with the coating with an additional piece of fiberglass mesh as a reinforcement.
• Apply 1st coat of Chemsol Chemroof Plus on the surface with a coverage of 0.45 Lit/Sqm/Coat all over the surface. While the coat is still wet, lay a 45 GSM fiberglass mesh over the surface. This mesh is sandwiched between two coats and provides a reinforcement to the coating. Let the coating air dry for minimum 6hrs.
• Apply 2nd coat of Chemsol Chemroof Plus at an angle of 90o to the first coat and let dry for minimum 6 hrs.
• Apply 3rd coat of Chemsol Chemroof Plus over the 2nd coat with 90o angle to the 2nd coat. Ensure that the fiber mesh is completely embedded in the coating and there are no air pockets left in the coating.

6. Ponding

• Let the system air cure for 7-8 days before pond test.
• Ponding shall be done with water not more than 5 cm in height.

Precautions and Limitations

• Do not dilute Chemroof Plus with water for coating application.
• Keep material closed when not in use.
• Corners, joints and repair areas should be treated with two extra coats.
• Not suitable for vehicular traffic.
• Surface must be in SSD condition for primer application.

Technical Information

Theoretical Coverage

Material consumption of 0.45 L/M2/Coat shall be maintained throughout three coats for a standard thickness of 800-1000 microns with fiber mesh. For a 20L pack of Chemroof Plus will cover approx. 150 m2 of area.

Storage

Chemsol Chemroof Plus shall be placed in a cool and dry place protected from direct sunlight.

Shelf Life

24 months for the date of manufacturing if unopened and stored properly.

Health and Safety

Wash skin with soap and water.
On eye contact wash the eyes immediately and consult a physician if irritation persists.
On ingestion consult a doctor immediately.

Chemsol Chemroof Kool is a single component polyurethane-based coating. It provides
excellent heat reduction and waterproofing for the metal surfaces.

Applications

• Factories
• Warehouses
• Metal sheets, aluminum roof surfaces, etc.

Features

• Excellent UV resistant.
• Increase life and durability of the structure.
• Non yellowing, anti-fungal and antibacterial.
• Easy to apply and clean.
• Excellent bonding to surface.
• Low dirt pickup.
• Highly elastic, tough and resilient coating that can bridge cracks up to 1 mm.

Method of Application

1. Surface Preparation

• Surface should be clean and dry and in sound condition.
• All the surface dirt, grease, loose particles, rust should be removed from the surface. And the surface should be washed thoroughly with clean water.
• All other previous coatings if any shall be completely removed.

2. Joint Treatment

• All the surface joints shall be cleaned properly and filled with PU sealant.

3. Priming

• Metal roofs shall be primed with Chem Zink Prime by roller or spray. The coverage should be 5-8 Sqm/L.

4. Application

• Apply 1 coat of Chemroof Kool on the primed surface with the help of roller or brush. Allow the coat to air dry for 6-8 hrs.
• Apply 2nd coat of Chemroof Kool on the first coat at 900 to the first coat. Let the system air cure for at least 7 days.

Precautions and Limitations

• Do not dilute Chemroof Kool with water.
• Stir the contents of the container before coating application.
• Keep material closed when not in use.
• Do not apply when rain is expected in short time span.
• Operating temperature for coating application is 10-40oC.

Technical Information

Theoretical Coverage

Material consumption of 8-9M2/L/Coat depending upon the porosity of the substrate.

Storage

Chemsol Chemroof Kool shall be placed in a cool and dry place protected from direct sunlight.

Pack Size

20L

Shelf Life

24 months for the date of manufacturing if unopened and stored properly.

Health and Safety

Wash skin with soap and water.
On eye contact wash the eyes immediately and consult a physician if irritation persists.
On ingestion consult a doctor immediately.

Chemsol Chemroof Clear is a transparent elastomeric waterproofing membrane which is strongly recommended for tiled surfaces, which adheres to the surface and provides excellent water-resistant coating.

This coating can be applied easily with the help of a roller or squeegee.

Applications

• Waterproofing tiled roofs and terraces.
• Coating on China Mosaic and other tiled surfaces.
• Clear coating for façade, tiled walls, bricks, etc.

Features

Easy to apply with brush, squeegee or roller.
• Good adhesion to tiled surface.
• Can be applied on both horizontal and vertical surfaces.
• Good UV resistance.

Method of Application

1. Surface Preparation

• Surface should be clean and dry and in sound condition.
• All the surface dirt, grease, loose particles should be removed from the surface. And the surface should be washed thoroughly with clean water.

All the tile joints should be completely filled with the help of appropri ate grout. Loose tiles shall be completely removed and fixed properly so as to avoid movement during use and coating application.

2. Priming

• Apply priming coat with Chemsol Chemroof Clear with 50% water dilution. The priming coat shall give approximate coverage of 80-100 Sqft/L depending upon the
  surface finish.

3. Application

• Mix the bucket contents thoroughly.
• The drain outlets need to be properly detailed with the coating with an additional piece of fiberglass mesh as a reinforcement.
• Apply 1st coat of Chemsol Chemroof Clear all over the surface. Let the coating air dry for minimum 6hrs.
• Apply 2nd coat of Chemsol Chemroof Clear at an angle of 90o to the first coat and let dry for minimum 6 hrs.
• Apply 3rd coat of Chemsol Chemroof Clear at an angle of 90O to the 2nd coat and let dry for minimum 6 hrs.

Precautions and Limitations

• Do not dilute Chemroof Clear with water for coating application.
• Keep material closed when not in use.
• Vehicular or machinery movement is not recommended on the coated surface.
• Use PU grade roller for the coating application.
• Do not apply excess material on the surface to avoid blistering on the coated surface.

Ś

Technical Information

Theoretical Coverage

Per liter coverage of 25 Sqft/Lit/3 Coats is obtained. Coverage depends upon porosity of the substrate.

Pack Size

5L and 20L

Storage

Chemsol Chemroof Clear shall be placed in a cool and dry place protected from direct sunlight.

Shelf Life

12 months for the date of manufacturing if unopened and stored properly.

Health and Safety

Wash skin with soap and water.
On eye contact wash the eyes immediately and consult a physician if irritation persists.
On ingestion consult a doctor immediately.